Regular tune-ups so that the results are primed to be done systematically according to the procedure. The procedure is usually contained in the manual or motor vehicle service manual. Often occurs after a car in tune up there even more damage. It happened because errors may occur during a tune up. Here are some things that you can pay attention to avoid mistakes that occur. : Always use original spare parts and qualified. If it can be as much as possible do not use fake parts are low quality because it can lower the vehicle's engine performance and even can cause wear on other engine components.When cleaning the combustion chamber cleaner do not use carbon (carbon deposit cleaning materials) because it will stick to the electrode spark plugs and cause the machine halting.
The use of carbon cleaner is recommended for cars that are often used in everyday life in the city streets but rarely used for distance and speed. After a long trip just using carbon cleaner, open the spark plug and clean all the deposits attached to the electrode. When removing spark plug wires spark plug wires do not exchange routes. Check spark plugs with the Ohm-meter, the right size for every 1200 Ohm 25 mm . When installing the spark plug back the hands should be clean and not wet in order to avoid a short circuit. At the time of entering the spark plugs, try not to hit the cylinder head because it can change the spark plug gap. Changes spark plug gap can affect engine performance. When installing the new platinum, do not get contaminated oil which is usually found on the rotor because if platinum is exposed to oil, it will cause premature burn surface. Use silicone grease lubricant specifically for platinum rotor .
Examination of oil should be done routinely. Do it in a flat area. To check the oil wait until the engine is cold because if you checked the engine oil when the engine just died last 3-4 minutes then the oil is still a lot left on the machine. This will cause the amount of oil in the crankcase is not appropriate. How to check the oil using the oil gauge milestones. Pull the oil gauge milestones and clean with a cloth and then re-enter as deeply as possible to obtain precise measurement results. Then pull the oil gauge and observe milestones. Oil must be between the sign F and L. If the oil is reduced, add the oil with the same viscosity level. The amount of oil should be present on the sign of F. Note the quality of the oil. If the oil has changed the color it needs to be replaced soon. See the instructions in the manual, the instructions are usually printed oil change every 6 months or after the car a distance of 5,000 km.
The use of carbon cleaner is recommended for cars that are often used in everyday life in the city streets but rarely used for distance and speed. After a long trip just using carbon cleaner, open the spark plug and clean all the deposits attached to the electrode. When removing spark plug wires spark plug wires do not exchange routes. Check spark plugs with the Ohm-meter, the right size for every 1200 Ohm 25 mm . When installing the spark plug back the hands should be clean and not wet in order to avoid a short circuit. At the time of entering the spark plugs, try not to hit the cylinder head because it can change the spark plug gap. Changes spark plug gap can affect engine performance. When installing the new platinum, do not get contaminated oil which is usually found on the rotor because if platinum is exposed to oil, it will cause premature burn surface. Use silicone grease lubricant specifically for platinum rotor .
Examination of oil should be done routinely. Do it in a flat area. To check the oil wait until the engine is cold because if you checked the engine oil when the engine just died last 3-4 minutes then the oil is still a lot left on the machine. This will cause the amount of oil in the crankcase is not appropriate. How to check the oil using the oil gauge milestones. Pull the oil gauge milestones and clean with a cloth and then re-enter as deeply as possible to obtain precise measurement results. Then pull the oil gauge and observe milestones. Oil must be between the sign F and L. If the oil is reduced, add the oil with the same viscosity level. The amount of oil should be present on the sign of F. Note the quality of the oil. If the oil has changed the color it needs to be replaced soon. See the instructions in the manual, the instructions are usually printed oil change every 6 months or after the car a distance of 5,000 km.
Tidak ada komentar:
Posting Komentar